ceramizer cs

CERAMIZER FOR 4-STROKE COMBUSTION ENGINES (CS)

€25.00

Benefits of using Ceramizer® – engine oil additive:

  1. Decreases fuel consumption by 3 to 15 %.
  2. Decreases oil consumption.
  3. Decreases the noise level and stabilizes the work of engine, improves the dynamics of the car.
  4. Equalizes compression pressure in cylinders.
  5. Regenerates friction surfaces.
  6. Facilitates starting the engine, especially in low temperatures.
  7. Ceramizer engine additive in many cases allows you to avoid expensive repairs and shields the engine against wear and tear processess.
  8. Regenerates friction surfaces during use, without the need to dismantle them. Restored surfaces are  durable and protected for 70000/100000 km (40000/60000 miles).Extends the operational life of friction pairs in the mechanism up to 5 times.
  9. Ceramizer engine oil additive substitutes for some repairs, reducing repair costs by a half in comparison with the traditional methods.
  10. Reduced friction factor to values of up to less than 0,02 – ten times lower then normal steel–steel friction.
  11. Longer operating period between oil changes (minimum 50% increase).
  12. In the event of oil leakage and loss, guaranteed continuous and safe use of vehicle (engine for up to 500 km/ 300 miles, gearbox, reducer, axle up to 1000 km/ 600 miles).
  13. Protection against corrosion and aggressive chemicals especially when lower quality fuel and lubricants are used.
  14. Decreased exhaust emission of toxic gases.
  15. Protection against piston ring seizure.
  16. Hardens and increases the wear and tear resistance of rubbing surfaces, up to 10 times. Microhardness- 4000-4500 MPa (400 – 450 kG/mm2 – for comparison microhardness of steel is 60 kG/mm2).
  17. Protection of natural environment.
  18. Ceramizer® may be used for any kind of machine or factory unit after consulting the manufacturer.

The process of regeneration as well as creation of ceramic surface occurs during use, without the need to dismantle the mechanism.

21 in stock

Product description

Ceramizer® CS is a preparation for regeneration and protection against wear of the friction surface of the engine. It can be used in all types of four-stroke engines.

Regeneration of the engine is carried out during the usual operation of the vehicle, dismantling the mechanism is not necessary. The only necessary action is to add the preparation to the infusion of engine oil. The ceramic oil additive produces a special ceramic-metal coating that builds up in places of friction of metal parts. Particularly intense action can be observed in the most worn areas.

The protection layer, created by the preparation for engine oil, eliminates all deformations and micro-damage to the engine. The use of Ceramizer® allows you to achieve an effect similar to micro-welding an additional layer of material in places that are characterized by the highest wear. The formation of a protective layer continues until about 1500 km is overcome.

 

Why is it worth using Ceramizer® CS engine regeneration preparation?

  • Parts of the engine, subject to frictional forces, are regenerated and become up to 5 times stronger.
  • The level of fuel consumption is significantly reduced. The observed savings range from 3 to 15%.
  • The engine runs quieter and more stable, and the vehicle moves more dynamically.
  • The phenomenon of oil uptake by the engine is significantly reduced.
Lower fuel consumption    Pobór olejuReduction of oil consumption
Quiet engine operation.     Engine regeneration

DOSAGING  – amount of doses, needed for ceramization of friction surfaces presented below:

Capacity of oil in the engine (in litres) –> 2-8 l 9-16 l 17-24 l 25-33 l
Mileage : 5- 50 000 km or 3-30000 miles 1/2 dose 1 dose 2 doses 3 doses
Mileage: 50 000- 300 000 km or 30 000- 180 000 miles 1 dose 2 doses 3 doses 4 doses
Mileage: over 300 000 km or 180 000 miles 2 doses 3 doses 4 doses 5 doses

PACKAGE includes:

  1. One dose of Ceramizer CS with net mass of 4 g.
  2. Instruction of use

RECOMMENDATIONS:

  1. Measure the  compression pressure (before and after treatment) in cylinders of the  engine – in order to confirm the effectiveness of Ceramizer and obtain tangible effects.
  2. Apply at any  stage , preferably directly at the oil change for optimally  long   period of  driving with Ceramizer®.
  3. Use primarily for  preventive reasons to protect the engine against the effects of friction, significantly prolonging its life..
  4. Ceramizer® can be used with any type of oil.
  5. During the full processing (1500 km) do not change oil.
  6. Use together with Ceramizer® for gearboxes, rear axles, power steering, fuel purifier.
  7. Ceramizer® can be used for any machines and factory units after consulting the Producer.

INSTRUCTION:

  1. Warm the engine up to 80-90 oC, by driving or keeping the engine going on the idle gear for at least 10 minutes.
  2. Turn the engine off.
  3. Unscrew the cap oil reservoir and pour the content of the syringe into the engine’s inlet.
  4. Turn the cap oil reservoir back on.
  5. Turn the engine on and leave it on the idle gear for 15 minutes.
  6. Drive carefully for 200 km / 125 miles (not necessarily at one time), not exceeding 2700 rotations/minute (the lower the rpm is, the higher friction in engine and the more effective creation of the coating of cermet is).
    Note: 200 km / 125 miles can be replaced by leaving the engine working for 4 hours on the idle gear. One hour on the idle gear – corresponds to 50 km / 30 miles drive.
  7. Engines which parameters are expressed in moto hours (mth) should be exploited within 5 mth (not necessarily at one time) not exceeding 2700 rotations/minute (rpm).
  8. Upon reaching 200 km / 125 miles or after 4 hours on the idle gear you can drive without rotations’  limitation. The metal-ceramic layer develops still up to 1500 km / 900 miles in normal operating conditions. During this time oil shouldn’t be changed.
  9. Engines which parameters are expressed in moto hours (mth) can be exploited without limitations after reaching 5 mth. The process of ceramization is completed after 30 mth.
  10. We recommend to double the dosage of Ceramizer® presented in  the instruction chart, if the engine absorbs oil. The first dose should be applied according to the directions for use, then after 500 km / 300 miles the second one should be applied in the same way.

 

REMARKS:

  1. If any teflon or molybdenum components had been added to oil before, we recommend to exchange this oil and to clean mechanism before appying Ceramizer® . Otherwise its effectiveness will be reduced and process of the cermet creation will be lengthened.
  2. In case of any mechanical damages of the engine e.g. cracked or scorched piston ring, leaky valve, deep scratches on the cylinder etc., they should be repaired before adding Ceramizer®.
  3. Ceramizer® does not recondition any places where friction of rubber or plastic with metal parts occurs.
  4. In case of engines without  automatic adjustment of valve clearance,  if after Ceramizer® treatment during 1500 km /900 miles, clatters of valves are heard, a regulation should be performed.
  5. If the engine is equipped with a centrifugal oil filter, it should be cleaned before applying Ceramizer®, and it is recommended to turn off the oil circulation while tooling, by using a tube (if possible). In these types of filters molecules tend to settle down, therefore the amount that reaches friction surfaces is reduced.
  6. The syringes are usable and the product is fully functional even if a small leakage of product under the pusher is noticed.

SAFETY:

  1. This product is safe in accordance with the UE (91/155/EEC) norm.
  2. Store at a temperature below +40 oC.
  3. Does not clog oil filters or oil ducts.
  4. Does not contain molybdenum or teflon. Can be safely used in engines with DPF.
  5. Keep away from children.

RESEARCH:

Effectiveness confirmed by multiple independent tests.

EFFECTIVENESS:

Ceramizer provides protection against wear and tear for minimum of 70 000 km/43 000 miles. Ceramizer® can be used again after this mileage.

Downloads

 

 

 

Weight 4 g

Reviews

There are no reviews yet.

Be the first to review “CERAMIZER FOR 4-STROKE COMBUSTION ENGINES (CS)”

Your email address will not be published. Required fields are marked *